Normes

This test method measures the thermal characteristics of windows, doors and glazed exterior wall sections under steady-state conditions. Specifically, measurements and calculations made using this procedure can be used to determine the thermal transmittance (air-to-air) or U-Factor, the air infiltration rate and/or the condensation resistance factor, hereafter called "CRF" for these products.

This guide outlines methods, equipment and materials applicable for cleaning architecturally finished aluminum after construction and for subsequent periodic maintenance. Methods outlined are intended for use on anodized or painted architectural products whether rolled or extruded shapes, including window and door frames, store fronts and entrances, curtain walls, mullions, columns, panels, hand rails, flag poles and hardware.

This specification describes test procedures and requirements for architectural quality aluminum oxide coatings applied to aluminum extrusions and panels for architectural products.

This guideline will permit the architect, owner and contractor to specify and obtain anodized aluminum finishes which will provide, with periodic maintenance, a superior level of performance in terms of film integrity, exterior weatherability, and general appearance for many years.

Includes 4/2015 Errata.

Guide to selecting pile weatherstrip and weatherseals used in windows and doors. Standards define requirements to restrict air and water infiltration. (editorially revised)

Covers production, specification, testing and proper handling of all types of anodic finishes and organic coatings for architectural aluminum curtain walls and their components.

This comprehensive aluminum finishing documents bundle includes all of the following documents (25% off the price compared to when purchased separately):

• AAMA 609 & 610-15
• AAMA 611-14
• AAMA 612-17
• AAMA 621-02
• AAMA 2603-17
• AAMA 2604-17
• AAMA 2605-17

Provides information on specific aspects of aluminum curtain wall construction. Contents: types, design concerns, detail guidelines and testing.

To provide up-to-date authoritative technical information in the belief that it will be of value not only to architects but to the architectural metals industry as well. Its ultimate aim is the promotion of good design practice, the use of quality materials and careful workmanship. The establishment of the adherence to appropriate standards in store front and entrance design will benefit all concerned; the architect, the manufacturer, the contractor and, most importantly, the building owner.
 
Please note that this document is the same as the AAMA Volume #3 - ALUMINUM STOREFRONT & ENTRANCE.

Design Wind Loads for Aluminum Curtain Walls 

Aluminum Curtain Wall Design Guides, Metal Curtain Wall Manual, Methods of Test, Technical Information Reports.CD purchases (new as of June, 2010) are a total savings of over 50% of the individual price of each document.

A complete guide to the design and specification of aluminum storefront and entrance systems

Please note that this document is the same as the AAMA SFM-1 - ALUMINUM STOREFRONT & ENTRANCE MANUAL.

Load and Resistance Factor Design for new bridges

The design standards for the maintenance and rehabilitation of older, existing structures.

Coating Damage - Fracture - Hot-Dip Galvanizing - Hot-Dip Process - Installation, Maintenance And Repair - Repair - Zinc Coated - Zinc-Coated Steel Products

Carbon steel shapes, plates, and bars of structural quality for use in riveted, bolted, or welded construction of bridges and buildings, and for general structural purposes.

Corrosive Service Applications - Fasteners - Hot-Dip Galvanizing - Hot-Dip Process - Zinc Coated - Zinc-Coated Steel Products

Bolts - Bolts, Screws and Studs - Carbon Steel - Chemical Composition - Steel - Studs - Tensile Strength

Quenched and tempered steel heavy hex structural bolts having a minimum tensile strength of 120 ksi for sizes 1.0 in. and less and 105 ksi for sizes over 1.0 to 11/2 in., inclusive

Bolts - Bolts, Screws And Studs - Carbon Steel - Hex Cap Screws - Quenching - Studs - Tempering - Tensile Strength - Weathering Steel

Quenched and tempered, alloy steel, heavy hex structural bolts having a tensile strength of 150 to 173 ksi

Atmospheric Corrosion Resistance - Bars, Rods And Rebars - Bridges - Carbon Steel - Corrosion Resistance - High-Strength Low-Alloy Steel - Hsla Steel - Plates - Quenching - Steel Bars - Steel Plates - Structural Steel - Tempering

Bronze castings for turntables, movable bridges and bridge parts, and bronze castings suitable for use in bridges and other structures for fixed and expansion bearings in which motion is slow and intermittent

Aluminum Alloy Castings - Aluminum Alloys - Castings - Sand Casting

Aluminum Alloy Castings - Aluminum Alloys - Castings - Permanent Mold Casting

Bars And Rods - Copper Alloy Plates - Copper Alloy Sheets - Copper Alloy Strips - Leaded Brass - Plates And Disks - Rolled Copper Alloy Bars - Sheet, Strips And Coils

Aluminum - Aluminum Alloy Plates - Aluminum Alloy Sheets - Aluminum Alloys - Plates - Sheet, Strips and Foils

Drawn Seamless Aluminum Alloy Tubes for General Purpose & Pressure Applications

Extruded Aluminum Alloy Tubes for General Purpose Applications. Aluminum - Aluminum Alloys - Bars And Rods - Rolled Aluminum Alloy Bars - Rolled Aluminum Alloy Rods - Rolled Aluminum Alloy Wires - Wires

Aluminum - Aluminum Alloys - Bars And Rods - Extruded Aluminum Alloy Bars - Extruded Aluminum Alloy Profile - Extruded Aluminum Alloy Rods - Extruded Aluminum Alloy Tubes - Extruded Aluminum Alloy Wires - Profiles - Seamless Pipes And Tubes - Wires

Drawn Seamless Aluminum Alloy Tubes for Condensers & Heat Exchangers

Seamless Extruded Aluminum Alloy Pipe & Tube for General Purpose & Pressure Applications

Aluminum - Aluminum Alloy Forgings - Aluminum Alloys - Die Forging - Forging - Forgings - Hand Forging - Rolled Ring Forging

Aluminum Alloy Angles - Aluminum Alloy Beams - Aluminum Alloy Channels - Aluminum Alloy Tees - Aluminum Alloy Zees - Aluminum-Magnesium-Silicon Alloys - Angles - Beams - Channels - Tees/Zees

Aluminum Alloy Round Welded Tubes

Extruded Aluminum Alloy Pipe for Electrical Bus Conductors

Seamless Extruded Aluminum Alloy Tubes & Pipe for Gas & Oil Transmission and Distribution Piping Systems

Pipe and tube is intended for use in structural applications such as highway and bridge rails, chain-link fence posts, handrails, sign structures, awning supports, lighting brackets

Drawn Aluminum Alloy Tubes for General Purpose Applications

Extruded Round Coiled Aluminum Alloy Tubes for General Purpose Applications

Aluminum Alloy Formed and Arc Welded Round Tube

Aluminum Alloy Arch Pipes - Aluminum Alloys - Corrugated Aluminum Alloy Plates - Corrugated Pipes And Tubes - Culverts - Drainage Piping - Fasteners - Pipe Arches - Sewer Pipes - Tubular Products

Corrosive Service Applications - Hull Structures - Hulls Structure Elements - Magnesium Alloy Plates - Magnesium Alloy Sheets - Magnesium-Aluminum Alloys - Marine Applications - Marine Engineering - Plates And Disks - Sheet, Strips And Coils

Classification of bare, wrought and cast aluminum-alloy electrodes, and rods for use with the gas metal arc, gas tungsten arc, oxyfuel gas, and plasma arc welding processes

Welding requirements for any type structure made from aluminum structural alloys

General requirements for the friction stir welding of aluminum alloys for aerospace applications

Technique du calcul aux états limites et définit les charges théoriques, combinaisons de charges et facteurs de charge, les critères pour une conception antisismique et critères de conception détaillés pour divers matériaux.
 
Pour acheter la norme, visitez le site internet de l’Association canadienne de normalisation (CSA).

Free-standing poles of ferrous metal, aluminum, polymeric, concrete, and wood, and to their accessories, for use in the support of lighting equipment. Poles used for the support of lighting equipment, such as luminaires, electric signs, and traffic lights.
 
Pour acheter la norme, visitez le site internet de l’Association canadienne de normalisation (CSA).

Tôles fortes, profilés, aux tôles, palplanches, profilés en C formés à froid, profilés de charpente creux, profilés en Z et barres en acier de construction.
 
Pour acheter la norme, visitez le site internet de l’Association canadienne de normalisation (CSA).

Énonce des exigences spécifiques aux bâtiments et les coefficients de charge et de tenue en service donnés doivent servir au calcul des composants d'éléments des bâtiments.
 
Pour acheter la norme, visitez le site internet de l’Association canadienne de normalisation (CSA).

Soudage par fusion de l'aluminium, qualification du personnel exécutant des soudures et modes opératoires de soudage.
 
Pour acheter la norme, visitez le site internet de l’Association canadienne de normalisation (CSA).

Soudage à l'arc sous gaz avec fil plein (GMAW), soudage à l'arc sous gaz avec électrode de tungstène (GTAW), soudage plasma (PAW) et le soudage des goujons en utilisant les procédés de soudage à l'arc et de soudage avec décharge de condensateurs.
 
Pour acheter la norme, visitez le site internet de l’Association canadienne de normalisation (CSA).

Qualification des inspecteurs en soudage (responsabilités et fonctions techniques).
 
Pour acheter la norme, visitez le site internet de l’Association canadienne de normalisation (CSA).

Réduction des répercussions économiques, environnementales et sociales négatives des activités de construction de bâtiments par la mise en application des principes de conception en vue du désassemblage et de l'adaptabilité (CDA).
 
Pour acheter la norme, visitez le site internet de l’Association canadienne de normalisation (CSA).

Définit les termes relatifs au soudage par friction-malaxage

Spécifie les exigences de conception relatives aux assemblages soudés par friction-malaxage

Spécifie les exigences relatives à la qualification des opérateurs soudeurs pour le soudage par friction-malaxage de l'aluminium

Spécifie les exigences relatives au descriptif et à la qualification des modes opératoires de soudage pour le soudage par friction-malaxage de l'aluminium

Spécifie une méthode permettant de déterminer l'aptitude d'un fabricant à utiliser le procédé de soudage par friction-malaxage pour la fabrication de produits ayant la qualité spécifiée. Elle spécifie des exigences de qualité, mais n'assigne pas ces exigences à un groupe spécifique de produits.

The properties of aluminum and its alloys which give rise to their widespread usage, with particular emphasis on manufacturability, recyclability, and corrosion resistance, are briefly described in this report. The designation system by which alloys are classified is also described, and references are provided for the reader who may desire more detailed information.

Aluminum By Design traces aluminum from its first use as a precious metal in the 19th century through its evolving role in daily life and explores how its unique properties inspired designers of furniture, jewelry, architecture, fashion and consumer and industrial products.

Strength design and load and resistance factor design aluminum Specification.

Standard Alloy & Temper Designation Systems for Aluminum supersedes.

Standard Dimensional Tolerances for Aluminum Mill Products (Metric version) supersedes (column headings and pipe size units for extruded and drawn pipe).

Standard Dimensional Tolerances for Aluminum Mill Products supersedes (column headings and pipe size units for extruded and drawn pipe).

Standard Designation System for Aluminum Hardeners reaffirms.

Standard Designation System for Unalloyed Aluminum reaffirms.

Standard Nomenclature System for Aluminum Metal Matrix Composite Materials.

Aluminum characteristics, alloy and temper designations, mill product specifications, nominal composition | Typical mechanical and physical properties, density calculation procedure, comparative characteristics and application, fabrication/ heat treatments of wrought aluminum and wrought aluminum alloy products | quality control and guidelines for testing, inspection, and identification |terminology associated with wrought aluminum products | standard limits for chemical composition, mechanical properties, physical properties and dimensional tolerances for wrought aluminum mill products; Designations for clad products; chemical composition limits | chemical composition, limits, mechanical property limits, dimensional tolerances, and other data classified by product form.

Aluminum characteristics, alloy and temper designations, mill product specifications, nominal composition | Typical mechanical and physical properties, density calculation procedure, comparative characteristics and application, fabrication/ heat treatments of wrought aluminum and wrought aluminum alloy products | quality control and guidelines for testing, inspection, and identification |terminology associated with wrought aluminum products | standard limits for chemical composition, mechanical properties, physical properties and dimensional tolerances for wrought aluminum mill products; Designations for clad products; chemical composition limits | chemical composition, limits, mechanical property limits, dimensional tolerances, and other data classified by product form.

The book is divided into three parts distinguished by their page colors: blue, yellow and white.

The blue section contains information on aluminum characteristics, alloy and temper designations, mill product specifications, nominal composition , typical mechanical and physical properties, density calculation procedure, comparative characteristics and application, fabrication/ heat treatments of wrought aluminum and wrought aluminum alloy products, and quality control and guidelines for testing, inspection, and identification. 

The yellow section lists the terminology associated with wrought aluminum products. The white pages cover standard limits for chemical composition, mechanical properties, physical properties and dimensional tolerances for wrought aluminum mill products; designations for clad products and chemical composition limits for aluminum mill products.

Details cleaning methods for mill-finished, anodized, chemical-coated, painted, porcelain enameled, plated and laminated aluminum finishes. It includes applications for architecture, transportation and home use. Also lists products, and manufacturers of products, for the care of aluminum, such as abrasive cleaners, etching cleaners, solvent and emulsion cleaners, clear organic coatings, mastic coatings, protective tapes and waxes and wipe-on coatings.

Provides a concise guide to the behavior of aluminum with a wide variety of food and chemicals.

Certain basic methods of dimensioning are important to enable the extruder to maintain reasonable efficiency in the manufacture of extrusion tools and in the inspection of extruded material. Adoption of these dimensioning methods by the customer will help insure that the extruder will obtain a suitable and economically produced product.

Guidance document includes discussion of dust sampling considerations, fire and explosion prevention strategies, engineering and administrative dust management controls, firefighting protocols, and management systems development. A must read for anyone responsible for managing dust in the aluminum environment.

A technical guide to the design of aluminum die forgings, it includes chapters on die design, tolerances for die forgings and forging drafting conventions. Numerous, detailed drawings are included.

Reduce the potential hazards in management of molten aluminum throughout the charging, melting, transferring, and casting processes.

Chemical composition limits and color codes for aluminum hardeners registered in accordance with the International Designation System for Aluminum Hardeners.

Chemical composition limits and color codes for aluminum hardeners registered in accordance with the International Designation System for Aluminum Hardeners.

Clad aluminum alloy products

Chemical composition limits for unalloyed aluminum referenced in a number of standards and specifications worldwide.

Chemical composition limits for aluminum alloys in the form of castings and ingot.

A pictorial publication which sets the correct terminology and definitions of cause for the attributes discussed. Two separate indexing systems for more than 150 attributes help the user identify the visual quality aspect being sought.

This publication sets the preferred terms and definitions of cause for the visual quality attributes of aluminum extrusions along with some illustrations.

This publication was developed for educational purposes and provides a broad description of how aluminum sheet and plate fabricated products are manufactured in an aluminum sheet mill.

Chemical compositions and physical and mechanical properties

Tolerances for aluminum alloy extrusions

Tempers for aluminum and aluminum alloy products | mechanical property data and other metallurgical characteristics specific to the alloy-temper combinations

Chemical composition limits for wrought aluminum and wrought aluminum alloys

Describes how proper shipping, handling and storing procedures can minimize water staining. Covered are: causes of water stains; packaging recommendations; inspection procedures; and recommendations for the prevention of stains. A "Dew Point Calculator Table" is featured, showing under what conditions water will condense on metal, increasing the possibility of staining. Also included are lists of instrument suppliers, manufacturers of moisture indicating labels, and suppliers of water stain preventatives.

Electrical uses of aluminum, including bare, covered and insulated wire and cable

Tempers for aluminum and aluminum alloy products | mechanical property data and other metallurgical characteristics specific to the alloy-temper combinations.